Clean heating and cooling - Siemens PLM Software facilitates energy-saving heat pump development
ThermoLift has developed the ThermoLift system at its headquarters in the Advanced Energy Center at the State University of New York, (SUNY). This device, which is driven by natural gas, combines air conditioning system and heat pump in a single unit. ThermoLift chose Siemens PLM Software solutions for the development and automated design optimization processes, as well as for simulating the design process. A very high number of components can be included in the simulation and multi-disciplinary simulations can be achieved in a single user interface by using Simcenter Star CCM +. The optimum design of the ThermoLift solution allows the energy costs for the heating, cooling and hot water systems in a building to be reduced by 30 to 50 percent compared to conventional systems.
ThermoLift has developed the ThermoLift system which combines air conditioning system and heating pump in a single unit which is driven by natural gas.
Most people in the USA use ovens or boilers to keep their houses and apartments warm. Only a small number use heat pumps which heat the buildings using environmental heat. These units are often electrically driven and this is the starting point for the founders of ThermoLift, Dr. Peter Hofbauer und Paul Schwartz. Their ThermoLift system for a modern heating, ventilation, and air conditioning (HVAC) system is similar to a standard Vuilleumier heat pump but uses a special temperature cycle (the TC cycle). In order to improve the simulation-led design process, ThermoLift has been working for a few years with the Simcenter simulation software from the Siemens PLM Software portfolio.
Precise simulation of extremely complex physics
A conventional Vuilleumier heat pump moves a gas such as helium between three chambers in a closed system. Two so-called displacers slide back and forth inside a cylinder. The expansion or compression of the gas occurs due to the cold or hot thermodynamic cycle. The particular feature of the ThermoLift device compared to a Vuilleumier heat pump is that the displacers are controlled separately from the mechatronics in order to provide better control of the displacer movement, and therefore the thermodynamic cycle. The whole ThermoLift system consists of several modules such as the heat exchanger, regenerators and displacers which are produced during the design process. ThermoLift chose Simcenter Star CCM + for the simulation and modelling of the complex physics involved. The software is a comprehensive solution which allows multi-disciplinary simulation in a single user interface. In addition to this, Star CCM + allows more components to be integrated into the simulation which speeds up the design process and produces even more accurate results.
Economical and reliable
The ThermoLift system's optimized design process means that the energy losses can be reduced significantly compared to conventional Vuilleumier heat pumps. This leads to energy cost savings of 30 to 50 percent. The displacers' 'soft landing' also reduces machine noise while achieving operating times of over ten hours.
05.09.2019, Siemens AG
此网站新闻材料的版权属于公司或第三方的新闻提供者，其所有权利保留。所有新闻材料对其访问者只能限于其本人使用，并且使用此材料的风险由其使用者独自自行承担。严禁对新闻材料进行再次发布和其它商业利用. 作为商业贸易的用途。如果新闻材料由第三方提供，当应用此新闻材料时，每个使用者都同意遵守，并且受此特定的项目的约束。Glass Global并不代表及认可新闻材料中所包含的内容及新闻中的外部网站的内容的准确性及可靠性。
Should the content or the design of these sites violate third parties rights or legal prescriptions, we kindly ask you to send us a respective message without invoice or cost. We guarantee that passages where the claim is considered as justified will be removed immediately, without any necessity to involve any lawyer into this issue. We will reject any claim caused by submission of a honorary note in this regard without any prior contact and confirmation of the issueby us and we reserve the right ssue counter claim ourselves because of violation of aforesaid conditions.